BSS Audio MSR-602 Series Instrukcja Użytkownika

Welcome to the MSR-602/604 II Users ManualWelcomeThis manual is provided to assist sound engineers, installers andconsultants to fully understand the

8MSR-600 II SeriesConnections and Control Descriptions3.0 Connections and Control DescriptionsF300MAL250V F3MAL250V F3MAL250VF10EFig. 2 MSR-602 II a

9AC Power Connections and Control SettingsBefore connecting the MSR-602 II to the AC power source, checkthat the voltage selector switch located on th

10MSR-600 II SeriesVoltage SettingSafety EarthingAC Power FusingThe mains voltage selector switch provides simple, external adjust-ment for operation

11ent connection of line to line rather than line to neutral phase voltageswhen using a three phase supply. In either case internal transientsuppress

12MSR-600 II SeriesThe audio connections to the MSR-604 II are via XLR style connectorson the front and rear panels and their wiring configuration is

13MSR-602 II ControlsSince all the audio connections are balanced, the convention of pin 2or pin 3 ‘hot’ is of no consequence provided all connections

14MSR-600 II Series3.5 MSR-604 IIControlsPHANTOM ON/OFFLINE/MICGAINCLIP LEDThe MSR-602 II power supply provides each MSR-604 II with 48v DCfor phant

15A 10dB input pad is activated when the channel detects a +48v phan-tom signal is present on the MAIN OUTPUT. This allows the front ofhouse mixing e

16MSR-600 II Series4.0 System Implementation and UseSystem Implementation and UseRackingIt is envisaged that a number of the MSR-604 II units will be

17the MSR-602 II. The MSR-602 II has a permanent safety ground con-nection via the power cord.Please read section 4.2 for discussion of grounding of

WARNING FOR YOUR PROTECTIONREAD THESE INSTRUCTIONS:KEEP THESE INSTRUCTIONSHEED ALL WARNINGSFOLLOW ALL INSTRUCTIONSDO NOT USE THIS APPARATUS NEAR WATER

18MSR-600 II SeriesGroundingFig. 7 MSR GroundingIn any multi-channel audio system where low level signals are beingrouted, it is important to ensure

19Channel CodingIn general the stage monitor console will be connected to the stagemains power grounding system so the signal connecting cables to the

20MSR-600 II Series4.4 Dual PowerSupply OperationThe power supply of the MSR-600 system performs a vital role withinthe sound system and although des

21The permissible settings are shown in Figure 11, and the effects ofeach on system gain and headroom is described in Table 2. Note thatcombinations

22MSR-600 II SeriesFig. 12 Bus Linking BlockDiagram.Default JumpersMultiple Output Distribution Amplifier ConfigurationJUMPER SETTINGFor use as a dis

23Fig. 13A Bus LinkingCh1 Drives Out1 and 2Ch3 Drives Out3 and 4Multiple Output Distribution Amplifier ConfigurationThe signal labelled EXBUS-OUT pas

24MSR-600 II SeriesMultiple Output Distribution Amplifier ConfigurationStereo Summing ConfigurationFig. 13B Bus LinkingIn1+In2 Drives Out1 and 2In3+In

25Limited compatibility exists between early MSR-604 systems andMSR604 II units using adaptor leads to interconnect the power cables.Please order adap

26MSR-600 II Seriestogether as described in section 3.2. Finally the pair of adaptor leadsare used to insert the Mk II units into the systems power c

27advice if a replacement or a second power supply is required for a MkI system.Figure 14 shows the block diagram of the audio section of the MSR-604

U.K. MAINS PLUG WARNINGA molded mains plug that has been cut off from the cord isunsafe. Discard the mains plug at a suitable disposal facili-ty. NE

28MSR-600 II SeriesTransient Suppressor ReplacementFig. 15 TransientSuppressor Detailsbalanced 10dB pad using a relay controlled by a circuit which m

29Figure 15 indicates the location and specification for the suppressors.In some situations it might be necessary to provide a transformerbalanced inp

30MSR-600 II Series8.0 Technical SpecificationsTechnical SpecificationsPlease order as ‘MSR-604 II balanced output transformer kit Z-MSRTX0II-01’. Th

31Stereo/Mono 1/4in Jack socketLoad Impedance 4Ω to 600ΩMax output 1W rmsLevel control -90dB to 0dBPower +/-27VDC, +48VDC from MSR-602 II PSU onlyCo

32MSR-600 II SeriesWeight 7.0 kg NetSize 1.75" x 19" x 11.6" (44 x 482 x 293mm)excluding connectorsShould you experience any difficulty

33This unit is warranted by BSS Audio to the original end user purchaseragainst defects in workmanship and the materials used in its manufac-ture for

34MSR-600 II SeriesUSER NOTES

35USER NOTES

36MSR-600 II SeriesUSER NOTES

2MSR-600 II SeriesFor continued compliance ensure that all input and output cables arewired with cable screen connected to pin 1 of the XLR. The input

3Table Of ContentsTable Of Contents1.0 Introduction 41.1 MSR-604 II Mic/Line Signal Splitter 51.2 MSR-602 II Power Supply Unit 62.0 Unpacking 72.1 War

4MSR-600 II Series1.0 IntroductionIntroductionIt is not uncommon within a sound system which uses microphones asa source of programme, for that microp

5MSR-604 II Microphone Signal Splitterflexibility of gain and level control, internal bus routing, signal meter-ing and a headphone monitoring facilit

6MSR-600 II SeriesMSR-602 II Power SupplyThe MSR-602 II is the system power supply providing all the neces-sary DC voltages for the MSR-604 II. It uti

72.0 UnpackingUnpackingWarrantyWarningAs part of our system of quality control, this product is carefullyinspected before packing to ensure flawless a